RadioLink AT10II Instruction Manual Download Page 62

Page: 62 / 88

Radiolink Electronic Ltd

www.radiolink.com

4.3.1

AILE DIFF (FIND IN ACRO FUNCTION MENU 3.3.5)

4.3.2 FLAPERON (GLID 1A+1F, FIND IN ACRO FUNCTION MENU 3.3.3)

4.3.3 V-TAIL (FIND IN ACRO FUNCTION MENU 3.3.10)

4.3.4 OFFSET (GLID 2A+2F):

Additional flight conditions are available specifically for sailplanes.

These additional flight conditions contain different offset trims to make the sailplane perform certain

maneuvers more easily. Aileron differential functions may be set to provide separate rates per

condition selected.

Prior to setting up OFFSET, you must active the conditions and assign the switches in the

CONDITION/FUNCTION.

Unnecessary fuselage motion is generated when there are sudden changes in the servo position

and variations in the operating time between channels can be suppressed by using the delay

function.

Note: The same delay amount for elevator and rudder is recommended when using V-tail

function.

The AT10II provides 5 additional setups along with the normal flight condition. (NORMAL,

START, SPEED, DISTANCE and LANDING) These offset trims have same setting abilities

basically except the switch and dial assignment. For an example of trim settings, please see the

following:

ADJUSTABILITY:

• Separate adjustments for each aileron, elevator, rudder and flap servo, for each condition.

• SWITCH G (AT10) or E (AT10) is programmed for NORMAL, START, and SPEED trims. SWITCH

C is programmed for DISTANCE and LANDING trims. These switch/position assignment is

adjustable. (CONDITION/FUNCTION)

• TRIM item (Digital trim operation mode):

NORM: normal trim operation mode.

MIX: offset rate trim operation mode while mixing is on.

• Optional assignable knob (CAMBER MIX) to allow trimming in flight of the aileron and flap action

of each flight condition.

• During OFFSET operation, the aileron and elevator travels are displayed on each trim display in

the Startup screen.

Goals

Steps

Inputs

Set up a START to gain

maximum possible lift on launch.

Each Aileron: 50%. Each Flap:

100%.

Elevator: -5% to compensate.

SWITCH (AT10II=G,

AT10II=E.)

Open OFFSET function

to BASIC .

again to ADVANCE

to OFFSET,

Switch to the START condition.

G or E from NORMA to START

Summary of Contents for AT10II

























































































Search results

Summary of Contents for AT10II

Reviews:

Related manuals for AT10II

Brands by name

Popular brands

RadioLink AT10II, Instruction Manual

Search results

Summary of Contents for AT10II

Reviews:

Related manuals for AT10II

Brands by name

Popular brands