RadioLink AT10II Instruction Manual Download Page 54

Page: 54 / 88

Radiolink Electronic Ltd

www.radiolink.com

Note: NOTE: If V-TAIL is active, you cannot activate ELEVON or AILEVATOR functions. If one of

these functions is active, an error message will be displayed and you must deactivate the last

function prior to activating ELEVON.

Note: Be sure to move the elevator and rudder sticks regularly while checking the servo motions.

If a large value of travel is specified, when the sticks are moved at the same time, the controls may

bind or run out of travel. Decrease the travel until no binding occurs.

Adjustability:

• Requires use of CH2 and CH4.

• Independently adjustable travels allow for differences in servo travels.

• Rudder differential is not available. (To create rudder differential, set RUD1 and 2 to 0, then use

two programmable mixes, RUD-ELE and RUD-RUD, setting different percents for up and down.

These are your new rudder travels. Trim and link off, switch assignment null so you can’t

accidentally turn off rudder.

3.3.11 ELEVON

ADJUSTABILITY:

• Requires use of CH1 and CH2.

• Independently adjustable aileron travel allows aileron differential.

• Independently adjustable elevator travel allows for differences in up vs. down travel.

• The separate ELEVON settings for each condition can be set. (GLID only)

Note: When changing the polarity of a rate, "change rate dir?" is displayed for a check. Please

set up after pressing DIAL for 1 second and canceling an alarm display. (GLID only)

Note: Be sure to move the elevator and aileron sticks to full deflection during setup. If large

travels are specified, when the AILERON and ELEVATOR STICKS are moved at the same time the

controls may bind or run out of travel.

Goals

Steps

Inputs

Activate

ELEVON.

Adjust aileron

down travel to

90% of up

travel, creating

aileron

differential.

Open ELEVON

to BASIC .

again to ADVANCE

to ELEVON,

Activate the function.

to MIX,PUSH

to ACT.

Summary of Contents for AT10II

























































































Search results

Summary of Contents for AT10II

Reviews:

Related manuals for AT10II

Brands by name

Popular brands

RadioLink AT10II, Instruction Manual

Search results

Summary of Contents for AT10II

Reviews:

Related manuals for AT10II

Brands by name

Popular brands