RadioLink AT10II Instruction Manual Download Page 43

Page: 43 / 88

Radiolink Electronic Ltd

www.radiolink.com

Sample reasons to use linear programmable mixes:

• To correct bad tendencies of the MULTIROTOR (such as rolling in response to rudder input).

• To operate 2 or more servos for a single axis (such as two rudder servos).

• To automatically correct for a particular action (such as lowering elevator when flaps are lowered).

• To operate a second channel in response to movement in a first channel (such as increasing the

amount of smoke oil in response to more throttle application, but only when the smoke switch is

active).

• To turn off response of a primary control in certain circumstances (such as simulating one engine

flaming -out on a twin, or throttle-assisted rudder turns, also with a twin).

Adjustability:

• Defaults: The 4 programmable mixes default to the most frequently used mixes for simplicity. If

you want to use one of these mixes, simply select that mix number so that the master and slave

servos are already selected for you.

• PROG.MIX1 aileron-to-rudder for coordinated turns

• PROG.MIX2 elevator-to-flap for tighter loops (HELI mixes default to ELEV-to-pitch.)

• PROG.MIX3 flap-to-elevator to compensate pitching with flaps (HELI mixes default to

pitch-to-ELEV)

• PROG.MIX4 throttle-to-rudder ground handling compensation

•Channels available to mix: All four mixes may use any combination of CH1-8. (CH9-10 is not

proportional and cannot be mixed.) Offset and dials may also be set to the master channels.

•Master: the controlling channel, the channel whose movement is followed by the slave channel.

•Another channel: Most mixes follow a control channel. (Ex: rudder-to-ailerons, 25%, no switch,

corrects roll coupling.)

MASTER SLAVE LINK

TRIM

SWITCH

POSITION

RATE OFFSET

RUDD

AILE ON

OFF

ANY

NULL

25% 0

•Offset as master: To create an OFFSET mix, set the master as OFST. (Ex: Move FLAPERON as

flaps 20% of their total throw when SWITCH C is in down position.)

MASTER

SLAVE

LINK

TRIM SWITCH POSITION RATE OFFSET

OFST

FLAP

ON N/A

DOWN

20% 0

•

Dial as master: To directly effect one servo’s position by moving a dial, set the master as the

desired dial. (Ex: create a second throttle trim on left slider.)

MASTER

SLAVE

LINK

TRIM

SWITCH POSITION RATE OFFSET

VR(D)

THRO

OFF

N/A

ANY

NULL

•Slave: the controlled channel. The channel is moved automatically in response to the movement of

the master channel. The second channel is in a mix’s name (i.e. aileron-to-rudder).

•Link: Link this programmable mix with other mixes.

Ex: PMIX FLAP-ELEVATOR mixing to correct for ballooning when flaps are lowered, but model has

a V-tail. Without LINK, this mix only moves CH2 elevator when flap is commanded, resulting in a

dangerous combination of yaw and roll. With LINK ON, mixing is applied to both CH2 and CH4.

MASTER SLAVE LINK

TRIM

SWITCH

POSITION

RATE

OFFSET

FLAP

ELEV

OFF

ANY

NULL

•Trim: Master’s trim affects slave. Not displayed if master is not CH 1-4, because 5-9 have no trim.

Ex: two rudder servos. With TRIM OFF, rudder trim would bind the two servos. TRIM ON resolves

this.

• On/off choices:

Summary of Contents for AT10II

























































































Search results

Summary of Contents for AT10II

Reviews:

Related manuals for AT10II

Brands by name

Popular brands

RadioLink AT10II, Instruction Manual

Search results

Summary of Contents for AT10II

Reviews:

Related manuals for AT10II

Brands by name

Popular brands