RadioLink AT10II Instruction Manual Download Page 36

Page: 36 / 88

Radiolink Electronic Ltd

www.radiolink.com

several levels of controllability.

【

TRAINR

】

MIX: INH

：

AILE NORM

：

ELEV NORM

：

THRO NORM

：

RUDD NORM

：

GEAR NORM

：

FLAP NORM

：

AUX1 NORM

：

AUX2 NORM

Adjustability:

• NORM: When the TRAINER SWITCH is ON, the channel set to this mode can be controlled by

the student. The set channel is controlled according to any programming set at the student's

transmitter.

• FUNC: When the TRAINER SWITCH is ON, the channel set to this mode can be controlled by

the student, controlled according to any mixing set at the instructor's transmitter.

• MIX: When the TRAINER SWITCH is ON, the channel set to this mode can be controlled by both

the student and the instructor, controlled according to any mixing set at the instructor's transmitter.

And the student's mixing rate is adjustable. (Default 30%)

[Note] However, it becomes invalid even if it sets up the channel which is not in a student's

transmitter. The channel serves as operation by the instructor's transmitter automatically.

• OFF: The channel set to this mode cannot be controlled by the student even when the TRAINER

SWITCH is ON. The set channel is controlled by the instructor only, even when the TRAINER

SWITCH is ON.

• SWITCH: controlled by spring-loaded SWITCH H only. Not assignable.

• Compatibility: The AT10 may be master or student with any Radiolink transmitter compatible with

the cord. Simply plug the optional trainer cord (For AT10 series, sold separately) into the trainer

connection on each transmitter, and follow the guidelines below.

EXAMPLES:

•When throttle/collective is set to FUNG, 5-channel helicopter practice is possible with a 4-channel

transmitter.

• Set up the model in a second transmitter, use NORM mode to quickly and safely check proper

operation of all functions, and then allow the student radio to fully fly the model.

• Using NORM mode, set lower throws, different exponentials, even different auxiliary channel

settings on the student radio (if it has these features).

• To ease the learning curve, elevator and aileron may be set to the NORM or FUNC mode, with

the other channels set to OFF and controlled by the instructor.

NOTE:

• NEVER turn on the student transmitter power.

•ALWAYS set the student transmitter modulation mode to PPM.

• BE SURE that the student and instructor transmitters have identical trim settings and control

motions. Verify by switching back and forth while moving the control sticks.

• FULLY extend the instructor's antenna. Collapse the student's antenna. (Except 2.4GHz)

• When the TRAINER function is active, the snap roll function is deactivated. Other functions, such

as IDLE-DOWN and THR-CUT, which have been assigned to the same switch, are not deactivated.

Always double check your function assignments prior to utilizing the TRAINER function.

•When you select a different model, the TRAINER function is deactivated in the current model for

safety reasons.

Goals

Steps

Inputs

Summary of Contents for AT10II

























































































Search results

Summary of Contents for AT10II

Reviews:

Related manuals for AT10II

Brands by name

Popular brands

RadioLink AT10II, Instruction Manual

Search results

Summary of Contents for AT10II

Reviews:

Related manuals for AT10II

Brands by name

Popular brands