RadioLink AT10II Instruction Manual Download Page 40

Page: 40 / 88

Radiolink Electronic Ltd

www.radiolink.com

Part 3. ACRO ADVANCE MENU FUNCTIONS

3.1 AIRPLANE WING TYPES (ACRO/GLID):

There are 3 basic wing types in MULTIROTOR models:

• Simple. Model uses one aileron servo (or multiple servos on a Y-harness into a single receiver

channel) and has a tail. This is the default setup and requires no specialized wing programming.

• Twin Aileron Servos. Model uses 2 aileron servos and has a tail. See TWIN AILERON SERVOS.

• Tail-less models (flying wing). Model uses 2 wing servos working together to create both roll and

pitch control. See ELEVON.

Twin Aileron Servos (with a tail) (ACRO/GLID): Many current generation models use two aileron

servos, plugged into two aileron servos, plugged into two separate receiver channels. (If your model

is a flying wing without separate elevators, see ELEVON)

ADVANTAGE:

• Ability to adjust each servo's center and end points for perfectly matched travel.

• Redundancy, for example in case of a servo failure or mid-air collision.

• Ease of assembly and more torque per surface by not requiring torque rods for a single servo to

drive 2 surfaces.

• Ease of assembly and more torque per surface by not requiring torque rods for a single servo to

drive 2 surfaces.

• Having more up aileron travel than down travel for straighter rolls, aileron differential. (See

glossary for definition.)

• Set a negative percentage to reverse the operation of one of the servos.

Options:

• 5-channel receiver. Set up AILE-2 prior to continuing with FLAPERON or AIL-DIFF.

• FLAPERON:

•Uses CH6 for the second servo

• Allows flap action as well as aileron action from the ailerons.

• Provides FLAP-TRIM function to adjust the neutral point of the FLAPERON for level flight.

• Also allows aileron differential in its own programming (instead of activating AIL-DIFF).

• Uses CH7 for the 2nd servo (see AIL-2 use CH5)

• Leaves CH5 & CH6 free for flap operation, such as FLAPERON and flap action together, in

Summary of Contents for AT10II

























































































Search results

Summary of Contents for AT10II

Reviews:

Related manuals for AT10II

Brands by name

Popular brands

RadioLink AT10II, Instruction Manual

Search results

Summary of Contents for AT10II

Reviews:

Related manuals for AT10II

Brands by name

Popular brands