manualshive.com logo in svg

Quantum Data 780C, User Manual

The Quantum Data 780C, a cutting-edge device, revolutionizes your multimedia experiences. Enhance your product understanding and maximize its potential with our comprehensive User Manual. Available for free download at manualshive.com, this manual provides detailed instructions and valuable insights to unlock the full capabilities of the Quantum Data 780C.

Share
Download
background image

780C Multi-Interface Interoperability Tester 

– User Guide 

Page 217 

September 29, 2014 

                                       Revision A1 

 

 

Table 12-1: List of Commands (alphabetical) 

– For Testing HDMI Sink Devices 

Command 

Description 

Syntax 

Parameters 

Command Example 

XAVI 

Enables you to send 
specific parameter 
values of the AVI 

infoframes out the 
HDMI outputs 
independent of the 

HDMI video stream 
parameters. 

XAVI:

aviparameter <value> 

Where aviparameter is one of the values identified 

below and value is an associated value provided in 
CEA-861-E. 
S – Scan information. Sets the scan information 
value or retrieves the value transmitted. 
B – Bar information. Sets the bar information value 

or retrieves the value transmitted. 
A – Active format information. Sets the active format 
information value or retrieves the value transmitted. 
C – Colorimetry. Sets the colorimetry value or 

retrieves the value transmitted. 
Y – Video type. Sets the video type value or 
retrieves the value transmitted. 
Q – RGB Quantization range. Sets the RGB 

Quantization range or retrieves the value 
transmitted. 
YQ – YCC quantization range. Sets the YCC 
quantization range or retrieves the value transmitted. 
R – Active Format Aspect Ratio. Sets active format 

aspect ratio value or retrieves the value transmitted. 
M – Picture Aspect Ratio. Sets the picture aspect 
ratio value or retrieves the value transmitted. 
EC – Extended Colorimetry. Sets the extended 

colorimetry value or retrieves the value transmitted. 
SC – Non-uniform Picture Scaling. Sets the non-
uniform picture scaling value or retrieves the value. 
ETB – Line number at start of top bar. Sets the pixel 
number start top value or retrieves the value 

transmitted. 
SBB – Line number at start of bottom bar. Sets the 
pixel number start bottom value or retrieves the 

value transmitted. 
ELB – Pixel number at start of left bar. Sets the pixel 
number start left value or retrieves the value 
transmitted. 
SRB – Pixel number at start of right bar. Sets the 
pixel number start right value or retrieves the value 
transmitted. 
VIC – Video Identification Code. Retrieves the value 

transmitted. 
PR – Pixel repetition. Sets the pixel repetition value 
or retrieves the value transmitted. 
ITC – IT Content. Sets the IT content value or 

retrieves the value transmitted. 
CN – Content Type. Sets the content type value or 
retrieves the value transmitted. 
CSUM – Checksum. Sets the checksum value or 
retrieves the value transmitted.

 

To set the scan parameter to 
overscanned: 

XAVI:S 1         
IFGU 

To set the video type to RGB 
and aspect ratio to 4:3: 

XAVI:Y 0; M 1 
IFGU 

To return the value of the video 
parameter type: 

XAVI:Y? 

Summary of Contents for 780C

















































































































































































































































Reviews:

No comments

Related manuals for 780C

Magnetic Instrumentation 2130 Instruction Manual preview
2130
Brand: Magnetic Instrumentation Pages: 63
Badger Meter Blancett B3100 Series User Manual preview
Blancett B3100 Series
Brand: Badger Meter Pages: 16
Badger Meter ModMAG M1000 User Manual preview
ModMAG M1000
Brand: Badger Meter Pages: 26
Badger Meter ModMAG M2000 Installation And Operation Manual preview
ModMAG M2000
Brand: Badger Meter Pages: 48
F&F LE-03 Quick Start Manual preview
LE-03
Brand: F&F Pages: 2
NanoEnTek JuLi Stage Installation Manual preview
JuLi Stage
Brand: NanoEnTek Pages: 4
VeEX MPA User Manual preview
MPA
Brand: VeEX Pages: 842
Major tech MT975 Instruction Manual preview
MT975
Brand: Major tech Pages: 16
Zoetis AlphaTRAK Instructions For Use preview
AlphaTRAK
Brand: Zoetis Pages: 2
AEMC MN307 User Manual preview
MN307
Brand: AEMC Pages: 4
Polimaster PM1703MO-1 Operation Manual preview
PM1703MO-1
Brand: Polimaster Pages: 6
STONEX R2W 2 PLUS 500 Instruction Manual preview
R2W 2 PLUS 500
Brand: STONEX Pages: 99
FASAR ELETTRONICA FE1023 Quick Start Manual preview
FE1023
Brand: FASAR ELETTRONICA Pages: 2
Velleman-Kit K4307 Manual preview
K4307
Brand: Velleman-Kit Pages: 9
Sagola Classic I 2 Instruction Manual preview
Classic I 2
Brand: Sagola Pages: 16
KEM RA-620 Operation Manual preview
RA-620
Brand: KEM Pages: 49
Xylem WTW SensoLyt 900 Operating Manual preview
WTW SensoLyt 900
Brand: Xylem Pages: 12
TDI LCR1 User Manual preview
LCR1
Brand: TDI Pages: 32

Brands by name

Popular brands

Load more brands