Quantum Data 780C User Manual Download Page 130

Page: 130 / 240

780C Multi-Interface Interoperability Tester

– User Guide

Page 129

September 29, 2014

Revision A1

The options:



Load File

– Loads from an EDID file stored on the 780C file system



Load TV Default

– Loads the standard reference EDID for a TV from the 780C file system



Load AVR Default - Loads the standard reference EDID for a AVR from the 780C file system

4. If you have selected the Load File option, the following screen results. Select the file that you wish to use

as the reference EDID. In the example below there is only one file.

The EDID is loaded and displayed on the screen.

Summary of Contents for 780C

















































































































































































































































Search results

Summary of Contents for 780C

Reviews:

Related manuals for 780C

Brands by name

Popular brands

Quantum Data 780C, User Manual

Search results

Summary of Contents for 780C

Reviews:

Related manuals for 780C

Brands by name

Popular brands