Quantum Data 780C User Manual Download Page 179

Page: 179 / 240

780C Multi-Interface Interoperability Tester

– User Guide

Page 178

September 29, 2014

Revision A1

4. Select

Frame Compare

to compare a series of frames to the reference frame.

The following screen example shows the results of the

Frame Compare

test. Note that the incoming

resolution is shown with the number of pixel errors detected.

9.2.3

Procedures for Running the Remote PRN Test

This subsection provides procedures for performing an HDMI Remote PRN test on an HDMI network
comprised of repeaters, splitters, extenders, switches, etc. This test differs in that there is a 780 at both ends of
the network

—source and sink ends.

1. Follow the procedures above for rendering a Test Pattern on an HDMI HDTV Rendering Test Patterns on

an HDMI HDTV.

Summary of Contents for 780C

















































































































































































































































Search results

Summary of Contents for 780C

Reviews:

Related manuals for 780C

Brands by name

Popular brands

Quantum Data 780C, User Manual

Search results

Summary of Contents for 780C

Reviews:

Related manuals for 780C

Brands by name

Popular brands