Quantum Data 780C User Manual Download Page 170

Page: 170 / 240

780C Multi-Interface Interoperability Tester

– User Guide

Page 169

September 29, 2014

Revision A1

You can view the details of each transaction and save the traces for viewing on the external ACA application
available from the Quantum Data website.

8.5.1

Procedures for Passive Monitoring HDMI CEC messages with the Auxiliary Channel Analyzer

This subsection provides procedures for ACA passive monitoring of CEC messages on HDMI devices.

Note

: You will have to obtain a license key for the ACA passive monitoring option to use the feature.

1. Connect the HDMI system devices to the 780C as shown in the diagram above and described as follows:

a. The HDMI source is connected to the 780C

ACA IN

connector.

b. The HDMI sink device (e.g. HDTV) is connected to the 780C

ACA OUT

connector.

2. From the

Home

screen (shown below) touch select the

Aux Channel Analyzer

activation button.

The

ACA Setup Options

screen appears:

Summary of Contents for 780C

















































































































































































































































Search results

Summary of Contents for 780C

Reviews:

Related manuals for 780C

Brands by name

Popular brands

Quantum Data 780C, User Manual

Search results

Summary of Contents for 780C

Reviews:

Related manuals for 780C

Brands by name

Popular brands