Quantum Data 780C User Manual Download Page 22

Page: 22 / 240

780C Multi-Interface Interoperability Tester

– User Guide

Page 21

September 29, 2014

Revision A1

4.1.2

Connecting the 780C to the Display Device - HDBaseT

Use the following procedures to make the physical connections from the 780C to the display device under test.

1. Make the cable connection between the appropriate the 780C video HDBaseT output connector and the

input connector of the HDBaseT device.

The following illustrations depict the typical test configurations.

4.1.3

Connecting the 780C to the Display Device - SDI

Use the following procedures to make the physical connections from the 780C to the display device under test.

1. Make the cable connection between the appropriate the 780C video SDI output connector and the input

connector of the display or monitor using the cables supplied.

Summary of Contents for 780C

















































































































































































































































Search results

Summary of Contents for 780C

Reviews:

Related manuals for 780C

Brands by name

Popular brands

Quantum Data 780C, User Manual

Search results

Summary of Contents for 780C

Reviews:

Related manuals for 780C

Brands by name

Popular brands