Quantum Data 780C User Manual Download Page 17

Page: 17 / 240

780C Multi-Interface Interoperability Tester

– User Guide

Page 16

September 29, 2014

Revision A1

3.3.3

Status Bar

The 780C has a status bar on the bottom of the screen.

The items in the status bar are described in the Table 3-2.

Table 3-2: Status Bar

Type

Status Item

Function

HDMI/HDBaseT/SDI IN

Video Type Status

Indicates the status of video on the

HDMI/HDBaseT/SDI Rx ports. This includes:



Video interface: HDMI or DVI, HDBaseT or

SDI



Color depth: 8, 10, 12



Video type: RGB or YCbCr



Sampling mode: 4:4:4, 4:2:2, 4:2:0

Note

: When SDI is active on the input, the Video

Type is always YCbCr and the sampling is always

4:2:2.

Video Resolution Status

Indicates the video resolution on the HDMI Rx port.
This includes:



Horizontal Active in pixels



Vertical Active in pixels



Frame rate

Summary of Contents for 780C

















































































































































































































































Search results

Summary of Contents for 780C

Reviews:

Related manuals for 780C

Brands by name

Popular brands

Quantum Data 780C, User Manual

Search results

Summary of Contents for 780C

Reviews:

Related manuals for 780C

Brands by name

Popular brands