Quantum Data 780C User Manual Download Page 47

Page: 47 / 240

780C Multi-Interface Interoperability Tester

– User Guide

Page 46

September 29, 2014

Revision A1

Table 4-6: Custom Test Image Packs

– ISF

Test Patterns

ISF Test Patterns

The ISF Pattern Pack offers patterns for verifying

white and black levels as well as geometry and
resolution for calibrating high end HDTVs

Black Pluge - for calibrating black level for dynamic range.

White Pluge - for calibrating white level for dynamic range.

Geometry/Resolution – test pattern to verify geometry and resolution.

Red-Blue Color Multiburst – test pattern for verifying chroma resolution for red and
blue transitions.

4.5

Outputting 3D Test Patterns through HDMI or HDBaseT

This subsection describes how to render 3D test patterns on an HDTV. The 780C supports Side-by-Side, Top-
and-Bottom and Frame Packing (for both interlaced and progressive timings) 3D format structures.

4.5.1

Configurations for Rendering 3D Bitmaps on an HDMI or HDBaseT Sink Device

Typically you will render 3D bitmap images with the 780C directly connected to an HDTV or projector. This
configuration is shown below:

Summary of Contents for 780C

















































































































































































































































Search results

Summary of Contents for 780C

Reviews:

Related manuals for 780C

Brands by name

Popular brands

Quantum Data 780C, User Manual

Search results

Summary of Contents for 780C

Reviews:

Related manuals for 780C

Brands by name

Popular brands