Quantum Data 780C User Manual Download Page 169

Page: 169 / 240

780C Multi-Interface Interoperability Tester

– User Guide

Page 168

September 29, 2014

Revision A1

8. Touch select the

Details

activation button (top center) to view the details of any specific transaction that

you have selected. The following screen is an example of the details screen. This example shows the
BCAPS register details. Touch select the

Details

activation button again to return to the trace view.

10. Touch select

Stop

activation button (top left) to halt the collection of messages.

11. Touch select

Clear

activation button (top center) to clear the collected of messages.

8.5

Auxiliary Channel Analyzer – Monitoring of CEC Messages

The Aux Channel Analyzer test monitors the CEC channel message while emulating HDMI/HDBaseT devices.

The features and functions described in this section are included only if you have purchased the
Auxiliary Channel Analyzer option.

Summary of Contents for 780C

















































































































































































































































Search results

Summary of Contents for 780C

Reviews:

Related manuals for 780C

Brands by name

Popular brands

Quantum Data 780C, User Manual

Search results

Summary of Contents for 780C

Reviews:

Related manuals for 780C

Brands by name

Popular brands