manualshive.com logo in svg

Quantum Data 780C, User Manual

The Quantum Data 780C, a cutting-edge device, revolutionizes your multimedia experiences. Enhance your product understanding and maximize its potential with our comprehensive User Manual. Available for free download at manualshive.com, this manual provides detailed instructions and valuable insights to unlock the full capabilities of the Quantum Data 780C.

Share
Download
background image

780C Multi-Interface Interoperability Tester 

– User Guide 

Page 15 

September 29, 2014 

                                       Revision A1 

 

 

RS-232 Baud Rate 

 

Configure the baud rate of the RS-232 interface 
on the 780C (N/A to 780). 

RS-232 Keypad Mode 

 

Off – Keypad connected to RS-232 is disabled. 

 

On – Keypad connected to RS-232 is enabled. 

Help 

Upgrades 

 

USB Storage Flash 

 

Application Flash 

 

FPGA Flash 

Touchscreen 

 

Calibrate the touch screen display 

Source Tests Buttons 

Format Analyzer 

Viewing Source Data Island Packet

 

Video Display 

Testing Video from an HDMI Source Device

 

Video Passthrough 

Viewing the Incoming 4K Video on a Connected Display using Passthrough

 

Packet Viewer 

Viewing Source Data Island Packet

 

HDCP Test 

Testing HDCP Max Devices on an HDMI Source Device

 

CEC Test 

Viewing the CEC devices on an HDMI network

 

Audio Analyzer 

Testing Audio of an HDMI Source Device

 

Audio Monitor 

Procedures for Monitoring LPCM Audio from a Source Device (780C only)

 

Sink Tests Buttons 

EDID Test 

Verifying the EDID on an HDMI HDTV or HDMI Repeater Device

 

HDCP Test 

Testing HDCP on an HDMI HDTV or HDMI Repeater Device

 

CEC Test 

Viewing the CEC devices on an HDMI network

 

Link Tests Buttons 

Aux Channel 
Analyzer 

Procedures for Monitoring Auxiliary Channel events and transactions

 

Cable/Repeater Test 

Using the 780C Test Instrument to Test HDMI Cable or Repeaters

 

Link Test 

Procedures for Installer Utility

 

Installer Tests Buttons 

Sink Tests 

Using the 780C Test Instrument Installer Utility

 

Source Tests 

Using the 780C Test Instrument Installer Utility

 

Repeater Tests 

Using the 780C Test Instrument Installer Utility

 

3.3.2

 

Back Navigation 

When you navigate away from the Home screen a white arrow will appear in the upper left next to the name of 
the of the screen you are on. You can navigate to the previous screen by touch selecting this arrow. In the 
example below, touch selecting the upper left area on or near the white, left facing arrow next to 

Signal Type

 

will take you to the previous screen. 

Summary of Contents for 780C

















































































































































































































































Reviews:

No comments

Related manuals for 780C

dacell DN-10 User Manual preview
DN-10
Brand: dacell Pages: 22
IFR COM-120B Evaluation Manual preview
COM-120B
Brand: IFR Pages: 46
Kamstrup MULTICAL 62 Technical Description preview
MULTICAL 62
Brand: Kamstrup Pages: 100
Kamstrup MULTICAL 41 Installation And User Manual preview
MULTICAL 41
Brand: Kamstrup Pages: 16
Kamstrup MULTICAL 41 Installation Manual preview
MULTICAL 41
Brand: Kamstrup Pages: 12
Kamstrup flowIQ 3100 Technical Description preview
flowIQ 3100
Brand: Kamstrup Pages: 60
Kamstrup MULTICAL 403 Technical Description preview
MULTICAL 403
Brand: Kamstrup Pages: 136
Kamstrup ULTRAFLOW 54 Installation Manual preview
ULTRAFLOW 54
Brand: Kamstrup Pages: 16
Kamstrup MULTICAL 603 Technical Description preview
MULTICAL 603
Brand: Kamstrup Pages: 155
Saimo 6101 Operating And Service Manual preview
6101
Brand: Saimo Pages: 101
Keit IRmadillo DOC1048R User Manual preview
IRmadillo DOC1048R
Brand: Keit Pages: 27
SAT-Kabel SPM 22 PF Operating Instructions Manual preview
SPM 22 PF
Brand: SAT-Kabel Pages: 12
Lutron Electronics VB-8213 Operation Manual preview
VB-8213
Brand: Lutron Electronics Pages: 23
Chauvin Arnoux PHYSICS line C.A 832 User Manual preview
PHYSICS line C.A 832
Brand: Chauvin Arnoux Pages: 43
Vega VEGAWAVE Supplementary Instructions Manual preview
VEGAWAVE
Brand: Vega Pages: 20
YoloLIV Instream User Manual preview
Instream
Brand: YoloLIV Pages: 18
S.E. International RADIATION ALERT Sentry Manual preview
RADIATION ALERT Sentry
Brand: S.E. International Pages: 8
SARAD Radon Scout Home Manual preview
Radon Scout Home
Brand: SARAD Pages: 2

Brands by name

Popular brands

Load more brands