Quantum Data 780C User Manual Download Page 69 | Manualshive

Page: 69 / 240

background image

780C Multi-Interface Interoperability Tester

– User Guide

Page 68

September 29, 2014

Revision A1

5

Using the 780C Test Instrument to Test HDMI and HDBaseT Protocols
on Sink Devices

This section provides procedures for testing HDMI or HDBaseT sink devices such as HDTVs, projectors and
inputs on repeater devices.

5.1

Testing HDCP on an HDMI, HDBaseT HDTV, Projector or Repeater

Device

This section provides procedures for testing HDCP on an HDMI or HDBaseT equipped HDTVs, projectors or
inputs on repeaters or distribution devices. The HDCP authentication test initiates and HDCP authentication
with the sink device (with or without a repeater) and displays the AKSV and BKSV values, the An value, the Ro
values and the Ri values. A pass/fail indication is provided as well.

5.1.1

Configurations for Testing HDCP on an HDMI Sink Device

You can run this test in two configurations.



780C HDMI OUT port connected directly to an HDTV input



780C HDMI OUT port connected to a repeater device which is then connected to a downstream HDTV.

These configurations are shown below:

5.1.2

Configurations for Testing HDCP on an HDBaseT Sink Device

You can run this test in two configurations.

«
...
67
68
69
70
71
...
»

Summary of Contents for 780C

















































































































































































































































Reviews:

No comments

Related manuals for 780C

TUNICS T100S-HP

Brand: Yenista Optics Pages: 66

Brand: TA Pages: 58

Brand: Rayjet Pages: 81

Brand: PAT Pages: 57

Brand: R&S Pages: 248

Brand: ColorLite Pages: 68

Brand: Omega Pages: 170

Brand: S.E. International Pages: 30

Brand: SZBJ Pages: 2

Brand: horiba Pages: 27

Brand: Sper scientific Pages: 56

Brand: Neogen Pages: 9

Brand: Teledyne Pages: 85

Brand: Hanna Instruments Pages: 16

Proline Promag 50H

Brand: Endress+Hauser Pages: 52

Brand: b&o Pages: 32

Brand: MFJ Pages: 8

DMX Laser40 FScan

Brand: KAM Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands