Quantum Data 780C User Manual Download Page 99

Page: 99 / 240

780C Multi-Interface Interoperability Tester

– User Guide

Page 98

September 29, 2014

Revision A1

Table 6-2: Format Analyzer

Color space

Color space and sampling
Color space:



YCbCr



RGB



xvColor

Sampling:



4:4:4



4:2:2



4:2:0

Basic colorimetry

The ITU colorimetry standard.

Pixels repeated

Indicates whether pixel repetition is active.

Video ID code (VIC)

The CEA video identification code number.

Resolution

Shows the horizontal and vertical resolution as well as the frame rate and the aspect ratio.

AVmute status

The current setting of the AVmute parameter in the General Control Packet.

HDCP

Indicates the HDCP encryption status either: 1) Encrypted or 2) Unencrypted.

6.1.6

Procedures for Viewing Video on an SDI Source Device

Use the following procedures to test the video from an SDI source device. You can view the incoming video
and check the video and timing parameters of the incoming video.

1. Make the physical connection between the 780C SDI IN port and the source device under test using the

configuration instructions above.

2. Enable the SDI Input port.

3. Touch select

Video Display

from the

Home

menu shown below.

Summary of Contents for 780C

















































































































































































































































Search results

Summary of Contents for 780C

Reviews:

Related manuals for 780C

Brands by name

Popular brands

Quantum Data 780C, User Manual

Search results

Summary of Contents for 780C

Reviews:

Related manuals for 780C

Brands by name

Popular brands