background image

-5-

Instructions on safe motorcycle riding

There should be a condition for the motorcycle to serve your well. The

condition is paying attention to safety at any time. Therefore, please observe
traffic laws and follow the six points below.

Wear safety helmet

Safe riding starts from wearing a safety helmet. This is an important

factor in motorcycle riding. A high-quality safety helmet is the first thing of
personal protection in motorcycle riding. The most serious traffic accident is
head injury. Therefore, be sure to wear a safety helmet to drive a motorcycle,
and wear a pair of proper protective glasses.

Please be familiar with the vehicle structure

Your riding technique and your understanding of mechanical knowledge

are the basis of safe riding. Make exercises in a spacious place without other
vehicle and make yourself fully familiar with your motorcycle and control
method. Be sure to keep in mind that, skill comes from practice.

Understand the limit of your safe speed

Riding speed depends on road surface conditions, your skills and the

weather. Understanding the limit may prevent accident. At any time, accident
may be prevented as long as riding in the range of your skill.

Wear well-fitting dress

Loose and fancy dress may make you uncomfortable and unsafe in your

riding. Riding on the cradle, a well-fitting dress may give you freedom for
activities of your arms and legs. Gloves, boots and safety helmet will show
that you are qualified driver. High quality and tight dress shouldbe your
selection.

Pay more attention to safety during riding in rainy weather

Wet roads are dangerous. Please note that, in rainy days, the braking

distance is two times as much as that in dry weather. Stay away from manhole
covers, paint marks or oily surfaces to prevent slipping. Avoid abrupt steering
during acceleration. Be careful when drive over railways and bridges and keep
a safe distance with any vehicle in front.

Inspection before riding

Please carefully read all instructions in "inspection before riding" of the

manual to guarantee the safety of you and passengers.

Position of serial numbers

Summary of Contents for QM110GY

















































Reviews: