ProMinent DULCOTROL DWCa Assembly And Operating Instructions Manual Download Page 99

Page: 99 / 140

CAL Cl

A1046

Accept with <CAL>

Zero point

Range

Fig. 62: Calibration of zero point
4.

Then press

CAL Cl

A1048

continue with <CAL>

Zero point

Slope

Calibration successful

Fig. 63: Calibration of zero point
5.

Import the result of the calibration into the controller memory

by pressing the key

The controller displays the continuous display again and

operates with the results of the calibration.

Incorrect calibration
Should the result of the calibration lie out‐

side the specified tolerance limits, an

error message appears. In this case the

current calibration will not be applied.
Check the prerequisites for the calibra‐

tion and clear the error. Then repeat the

calibration

15.1.5 Calibrating the oxygen sensor

15.1.5.1

Specify the calibration interval

The calibration interval depends strongly on:

the application

the installation location of the sensor

Calibrating the controller diaLog DACb

Summary of Contents for DULCOTROL DWCa













































































































































Search results

Summary of Contents for DULCOTROL DWCa

Reviews:

ProMinent DULCOTROL DWCa, Assembly And Operating Instructions Manual, Page: 99 / 140

Search results

Summary of Contents for DULCOTROL DWCa

Reviews: