ProMinent DULCOTROL DWCa Assembly And Operating Instructions Manual Download Page 77

Page: 77 / 140

CAL pH

Last calibration

A1016

Zero point

Slope

Calibration process

CAL setup

continue with <CAL>

14:26:07

7,00 pH

2 point

56.64mV/pH

06/04/2013

Fig. 37: pH sensor calibration (CAL)
1.

Continue with .

Rinse the sensor thoroughly with water and dry with a cloth

(pat dry, don't rub).

Immerse the sensor in test container 1 which contains the

buffer solution (e.g. pH 7). Gently move the sensor.

Continue with .

Do not move the sensor cable during calibra‐

tion as this can lead to signal variations.

Calibration is running .

[Please wait!] flashes.

Sensor voltage

Sensor calibration in buffer 1

A1017

Buffer temperature

Stability

acceptable

good

Continue with <CAL>

Fig. 38: Display of the sensor stability achieved
5.

The range

[acceptable / good / very good] is displayed.

The black part of the horizontal bar indicates the deter‐

mined range.

As soon as the black bar appears, the display changes from

[Please wait!] to continue with .

The black bar does not need to be at

[very good].

Calibrating the controller diaLog DACb

Summary of Contents for DULCOTROL DWCa













































































































































Search results

Summary of Contents for DULCOTROL DWCa

Reviews:

ProMinent DULCOTROL DWCa, Assembly And Operating Instructions Manual, Page: 77 / 140

Search results

Summary of Contents for DULCOTROL DWCa

Reviews: