ProMinent DULCOTROL DWCa Assembly And Operating Instructions Manual Download Page 83

Page: 83 / 140

CAL pH

Calibration process Data input

A1024

Zero point

Slope

Last calibration

CAL setup

continue with <CAL>

16:47:32

7,00 pH

59.16 mV/pH

06/05/2013

Fig. 43: pH sensor calibration (CAL)
1.

Continue with .

CAL pH

6.88 pH

Slope

at 25.0 °C

A1026

-58.07 mV/pH

continue with <CAL>

Asymmetry

at 25.0 °C

Zero point

at 25.0 °C

-6.4 mV

Fig. 44: Selection of the settable parameters
2.

Use the arrow keys to select the required menu entry and

press .

The Enter window appears.

Use the arrow keys to enter the values of your sensor and

press .

Continue with .

Incorrect calibration
An error message appears if the result of the cali‐

bration lies outside the specified tolerance limits. In

this case the current calibration is not carried over.
Check the prerequisites for calibration and elimi‐

nate the error. Then repeat calibration.

Carry over the result of the calibration into the controller

memory by pressing .

The controller shows the continuous display again and

operates with the results of the calibration.

Calibrating the controller diaLog DACb

Summary of Contents for DULCOTROL DWCa













































































































































Search results

Summary of Contents for DULCOTROL DWCa

Reviews:

ProMinent DULCOTROL DWCa, Assembly And Operating Instructions Manual, Page: 83 / 140

Search results

Summary of Contents for DULCOTROL DWCa

Reviews: