manualshive.com logo in svg

ProMinent DULCOTROL DWCa, Assembly And Operating Instructions Manual, Page: 6 / 140

Share
Download
ProMinent DULCOTROL DWCa Assembly And Operating Instructions Manual Download Page 6

1 

Identity code ordering system for DULCOTROL

®

 measuring

and control panels

Identity code ordering system for DULCOTROL

®

 measuring and control panels

DWCa DULCOTROL measuring and control system

Application
P Potable water (for "sample water” H,1 or 2)
W Waste water (for “sample water” H, 4, 5 or 7)
  Sample water

1 Potable water / product water, T< 45 °C
2 Rinsing water / industrial water / process water, T< 45 °C
4 Clear waste water
5 Waste water with solid particle fraction, turbid
7 Waste water with fluoride and pH < 7
H Hot water to max. 65 °C, at max. 2 bar (measured variables C1, P0, R0, L0 only).
  Channel 1, measured variable 1

C0 Free chlorine < pH 8
C1 Free chlorine > pH 8 and/or contaminated water
G0 Total chlorine (free and combined chlorine)
P0 pH
R0 ORP
D0 Chlorine dioxide
I0

Chlorite

L0

Conductivity

Z0

Ozone

F0

Fluoride (pH min.= 5.5, pH max. = 8.5)

H0 Hydrogen peroxide
A0 Peracetic acid
X0 Dissolved oxygen
 

Channel 2, measured variable 2 (optional) **
00

none

C0

Free chlorine < pH 8

C1

Free chlorine pH value > 8.0 and/or contaminated water

G0

Total chlorine (free and combined chlorine)

P0

pH

R0

ORP

D0

Chlorine dioxide

I0

Chlorite

L0

Conductivity

Identity code ordering system for DULCOTROL

®

 measuring and control panels

 

 

 

6

Summary of Contents for DULCOTROL DWCa













































































































































Reviews:

No comments