ProMinent DULCOTROL DWCa Assembly And Operating Instructions Manual Download Page 81

Page: 81 / 140

CAL pH

Calibration process

A1023

Zero point

Slope

Last calibration

CAL setup

continue with <CAL>

06/05/2013 14:26:07

Sample (1-point)

Buffer temperature

Manual

Fig. 41: pH sensor calibration (CAL)
1.

Continue with

Take a water sample at the in-line probe housing and, using

a suitable method (measuring strips, hand measuring instru‐

ment), measure the pH value of the sample

CAL pH

Change with <OK>

A1022

2) Determine pH value

pH value

continue with <CAL>

1) Take sample

Fig. 42: Instructions for determining the pH value using the

[Sample] method
3.

Press

Use the arrow keys to enter the pH value you have deter‐

mined in the controller

Press

Accept the pH value by pressing

All the values of the calibration result are shown in the

display.

Incorrect calibration
An error message appears if the result of the cali‐

bration lies outside the specified tolerance limits. In

this case, the current calibration is not applied.
Check the prerequisites for calibration and clear

the error. Then repeat calibration.

Transfer the result of the calibration into the controller

memory by pressing

The controller displays the continuous display again and

operates with the results of the calibration.

Calibrating the controller diaLog DACb

Summary of Contents for DULCOTROL DWCa













































































































































Search results

Summary of Contents for DULCOTROL DWCa

Reviews:

ProMinent DULCOTROL DWCa, Assembly And Operating Instructions Manual, Page: 81 / 140

Search results

Summary of Contents for DULCOTROL DWCa

Reviews: