ProMinent DULCOTROL DWCa Assembly And Operating Instructions Manual Download Page 70

Page: 70 / 140

Calibrating the controller diaLog DACb

15.1 Calibration

User qualification: instructed user,

Chapter 2.5 ‘User qualifi‐

cation’ on page 15

Measuring channel settings
This descriptions of [Channel 1] apply correspond‐

ingly to the settings in all other measuring chan‐

nels. The procedure for entering the settings for

the channel in question is identical, however the

parameters to be set may differ. Your attention is

drawn to the differences, which are also described.

Display tolerances
Display tolerances between the sensor and/or

measuring device and controller must be calibrated

with sensors and/or with output signals from meas‐

uring devices that do not require calibration or

where calibration is performed in the sensor/meas‐

uring device. The relevant information for this is

contained in the respective operating instructions

for the sensor or measuring device.

Cancelling the calibration process with ESC
ESC can be used to cancel an ongoing calibration

process at any stage. The controller then con‐

tinues to operate with the last calibration result

detected as valid.

Continuous display ➨ Menu ➨ or

[Calibration] ➨ .

or
Continuous display ➨ .

A1606

Channel 2

Channel 1

Please select channel

pH [mV]

Calibration

Chlorine

Fig. 31: Please select the channel.

Calibrating the controller diaLog DACb

Summary of Contents for DULCOTROL DWCa













































































































































Search results

Summary of Contents for DULCOTROL DWCa

Reviews:

ProMinent DULCOTROL DWCa, Assembly And Operating Instructions Manual, Page: 70 / 140

Search results

Summary of Contents for DULCOTROL DWCa

Reviews: