ProMinent DULCOTROL DWCa Assembly And Operating Instructions Manual Download Page 111

Page: 111 / 140

Apply the result of the calibration by pressing .

The controller shows the calibration menu again and

operates with the results of the calibration.

Incorrect calibration
An error message appears if the result of

the calibration lies outside the specified

tolerance limits. In this case, the current

calibration is not carried over.
Check the prerequisites for calibration

and eliminate the error. Then repeat cali‐

bration.

15.1.9 Calibrating temperature

Measuring and control behaviour of the controller

during calibration
During calibration the actuating outputs are deacti‐

vated. Exception: a basic load or a manual control

variable has been set. This remains active. The

measured value output [standard signal output mA]

is frozen, corresponding to its settings in the mA

output menu.
When calibration/testing has been completed suc‐

cessfully, all of the error checks relating to the

measured value are restarted. The controller saves

all the determined data for zero point and slope

upon a successful calibration.

You may need a manual measuring instrument for the temperature

measured variable. This manual instrument should measure and

display sufficiently accurately to guarantee successful calibration.
1.

Press in the continuous display.

Then press

Follow the instructions in the controller display and perform

calibration

Then press

Then press to adjust the value or press to continue with

calibration

Import the result of the calibration into the controller memory

by pressing

The controller shows the continuous display again and

operates with the results of the calibration.

Incorrect calibration
An error message appears if the result of

the calibration lies outside the specified

tolerance limits. In this case the current

calibration is not carried over.
Check the prerequisites for calibration

and eliminate the error. Then repeat cali‐

bration.

Calibrating the controller diaLog DACb

111

Summary of Contents for DULCOTROL DWCa













































































































































Search results

Summary of Contents for DULCOTROL DWCa

Reviews:

ProMinent DULCOTROL DWCa, Assembly And Operating Instructions Manual, Page: 111 / 140

Search results

Summary of Contents for DULCOTROL DWCa

Reviews: