manualshive.com logo in svg

ProMinent DULCOTROL DWCa, Assembly And Operating Instructions Manual, Page: 33 / 140

Share
Download
ProMinent DULCOTROL DWCa Assembly And Operating Instructions Manual Download Page 33

8 

Installing sensors in the bypass fitting DLG III/IV

n

User qualification, mechanical installation: trained qualified per‐

sonnel, see 

Ä

 Chapter 2.5 ‘User qualification’ on page 15

n

User qualification, hydraulic installation: trained qualified per‐

sonnel, see 

Ä

 Chapter 2.5 ‘User qualification’ on page 15

n

User qualification, electrical installation: Electrical technician,

see 

Ä

 Chapter 2.5 ‘User qualification’ on page 15

WARNING!
Danger from hazardous substances!
Possible consequence: Fatal or very serious inju‐

ries.
Please ensure when handling hazardous sub‐

stances that you have read the latest safety data

sheets provided by the manufacture of the haz‐

ardous substance. The actions required are

described in the safety data sheet. Check the

safety data sheet regularly and replace, if neces‐

sary, as the hazard potential of a substance can be

re-evaluated at any time based on new findings.
The system operator is responsible for ensuring

that these safety data sheets are available and that

they are kept up to date, as well as for producing

an associated hazard assessment for the worksta‐

tions affected.

CAUTION!
– Observe the maximum permissible operating

parameters for the entire installation (e.g. pres‐

sure, temperature, flow).

– In this respect, consider the lowest maximum

permissible operating parameters for the parts

of the DULCOTROL

®

 measuring/control station

and the integrated sensors; see their operating

instructions.

– Please also observe the operating instructions

for any other units, such as sensors, sample

water pumps ...

– Bear in mind the direction of flow of the sample

water.

– Do not exceed the maximum operating pres‐

sure.

– Fit an appropriate pressure reducer if unavoid‐

able.

– Danger due to pressurised media. Before

working on the hydraulic part of the

DULCOTROL

®

 measuring/control station,

ensure in a controlled manner that this part is

at atmospheric pressure using the sampling

tap.

– Wear safety goggles.

Installing sensors in the bypass fitting DLG III/IV

 

 

 

33

Summary of Contents for DULCOTROL DWCa













































































































































Reviews:

No comments