Polaris RANGER CREW 900 2014 Manual Download Page 372 | Manualshive

Page: 372 / 447

background image

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual
© Copyright Polaris Sales Inc.

9.19

CALIPER ASSEMBLY

1.

Install new O-rings in the caliper body. Be sure the
grooves are clean and free of residue or brakes may
drag upon assembly.

2.

Coat pistons with clean Polaris DOT 4 Brake Fluid.
Install pistons with a twisting motion while pushing
inward. Piston should slide in and out of bore
smoothly, with light resistance.

3.

Lubricate the mounting bracket pins with silicone
grease and install the rubber dust seal boots.

4.

Compress the mounting bracket and make sure the
dust seal boots are fully seated. Install the brake
pads. Clean the disc and pads with brake parts
cleaner or denatured alcohol to remove any dirt, oil
or grease.

CALIPER INSTALLATION

1.

Install

caliper

and

torque

mounting

bolts

to

specification.

NOTE

If brake disc scraper (A) was removed, be sure to

reinstall it upon caliper installation.

TORQUE

Front Caliper Mounting Bolts:

30 ft-lbs (41 Nm)

2.

Install brake line and torque the banjo bolt to the
proper torque specification.

«
...
370
371
372
373
374
...
»

Summary of Contents for RANGER CREW 900 2014
































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RANGER CREW 900 2014

Brand: ODES UTVS Pages: 141

Brand: Baja motorsports Pages: 44

Brand: MANCO Pages: 4

Brand: Tomberlin Pages: 40

Brand: E-Z-GO Pages: 180

Brand: Yetti Pages: 42

Brand: Landoll Pages: 72

Sasquatch Youth 800W

Brand: Daymak Pages: 24

2005 WILD HP 450

Brand: GAS GAS Pages: 63

Brand: FIORENTINI Pages: 21

Viking YXM70VPXH 2016

Brand: Yamaha Pages: 172

Brand: WilTec Pages: 7

Cushman HAULER 800X ELiTE 2019

Brand: Textron Specialized Vehicles Pages: 66

Brand: TrailMaster Pages: 30

Brand: TrailMax Pages: 65

Brand: TrailMax Pages: 72

THE INTERCEPTOR BT-57

Brand: Westward Pages: 692

Track-O Twin-Track 47

Brand: Movex Pages: 37

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands