Polaris RANGER CREW 900 2014 Manual Download Page 346

Page: 346 / 447

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual
© Copyright Polaris Sales Inc.

8.27

16. Torque the locking screw to specification.

TORQUE

Snorkel Locking Screw:

8-10 ft-lbs (11-14 Nm)

Transmission Assembly

NOTE

The snorkel shaft and pinion shaft must be installed

prior to transmission assembly. The snorkel shaft

cannot be installed after assembling the transmission.

17. Clean both transmission case halves thoroughly.

Inspect case half mating surfaces for damage.

18. Install

shift

fork

(S)

and

torsion

spring

into

transmission housing as an assembly. Load spring
as shown in image below

19. Apply Loctite® 242 to (2) screws (T) and install with

retaining

plates

over

shift

fork.

Torque

specification.

TORQUE

Shift Fork Screws:

7-10 ft-lbs (10-14 Nm)

20. Slide engagement dog (U) onto retaining pins of shift

fork.

21. Assemble the reverse shaft assembly and input shaft

assembly

previously

disassembled

(see

illustrations).

TRANSMISSION

Summary of Contents for RANGER CREW 900 2014
































































































































































































































































































































































































































































Search results

Summary of Contents for RANGER CREW 900 2014

Reviews:

Related manuals for RANGER CREW 900 2014

Brands by name

Popular brands

Polaris RANGER CREW 900 2014, Manual

Search results

Summary of Contents for RANGER CREW 900 2014

Reviews:

Related manuals for RANGER CREW 900 2014

Brands by name

Popular brands