Polaris RANGER CREW 900 2014 Manual Download Page 274 | Manualshive

Page: 274 / 447

background image

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual
© Copyright Polaris Sales Inc.

6.25

DRIVEN CLUTCH SERVICE

EXPLODED VIEW

CLUTCH DISASSEMBLY / INSPECTION

CAUTION

Wear eye protection when removing snap ring to

prevent serious personal injury.Use caution when
removing, the snap ring pressure is loaded by the

compression spring.

1.

Remove driven clutch from transmission input shaft.

2.

Mark the position of the clutch sheaves before
disassembly or use the X’s on the sheaves for
reference. This aids in reassembly and maintains
clutch balance after reassembly.

3.

Place the driven clutch into the Universal Clutch
Compressor

PU-50518.

Apply and hold downward

pressure on the outer spring retainer. Carefully
remove the snap ring (A). Remember the outer
spring retainer (B) contains strong spring pressure.

NOTE

Spring is compression only and has no torsional wind.

«
...
272
273
274
275
276
...
»

Summary of Contents for RANGER CREW 900 2014
































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RANGER CREW 900 2014

Brand: Razor Pages: 2

Brand: Bad Boy Pages: 56

2002/24 ATV-300XS

Brand: HER CHEE Pages: 56

Brand: CF MOTO Pages: 365

Brand: Landoll Pages: 82

Brand: Club Car Pages: 60

Brand: Yamaha Pages: 222

YXZ 1000 R SS 2023

Brand: Yamaha Pages: 216

Brand: Suzuki Pages: 477

Brand: Yamaha Pages: 87

WOLVERINE 350 YFM25XX

Brand: Yamaha Pages: 126

WOLVERINE 350 YFM35XY

Brand: Yamaha Pages: 128

Brand: Yamaha Pages: 108

Wolverine YFM350FXK

Brand: Yamaha Pages: 156

Brand: Yamaha Pages: 150

Wolverine YFM350FXL

Brand: Yamaha Pages: 164

Venture Lite PZ50GTB Venture Lite PZ50MTB

Brand: Yamaha Pages: 100

Brand: Yamaha Pages: 166

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands