Polaris RANGER CREW 900 2014 Manual Download Page 38 | Manualshive

Page: 38 / 447

background image

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual
© Copyright Polaris Sales Inc.

2.21

4.

Remove the spark plug wires (D) from the engine.

5.

Remove the (4) T40 bolts (E) and rubber isolators (F)
retaining the valve cover (G). Note the location and
use of the grounding washer (H) for assembly.

NOTE

Replace rubber isolators (F) upon assembly.

6.

The engine will need to be rotated (4) times to
inspect all (8) valve clearances. Two valves can be
measured at each camshaft lobe position.

NOTE

Remove spark plugs to aid engine rotation.

7.

Rotate the drive clutch counter-clockwise until the
cam lobes above the valves you are inspecting are
facing up.

«
...
36
37
38
39
40
...
»

Summary of Contents for RANGER CREW 900 2014
































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RANGER CREW 900 2014

Brand: Yamaha Pages: 54

Brand: Yamaha Pages: 60

Brand: Yamaha Pages: 60

Brand: Yamaha Pages: 68

Brand: Yamaha Pages: 70

Brand: Yamaha Pages: 84

Brand: Yamaha Pages: 90

Brand: Yamaha Pages: 174

Brand: Yamaha Pages: 198

Brand: HOMCOM Pages: 35

Brand: Can-Am Pages: 144

Brand: KMW Pages: 98

Brand: Tao Motor Pages: 73

Brand: E-TON Pages: 35

Brand: Hammerhead Off-Road Pages: 75

Sasquatch 800 UTV

Brand: Daymak Pages: 16

Off-Roader 125-4

Brand: Texas Pages: 32

Brand: Sauber Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands