Polaris RANGER CREW 900 2014 Manual Download Page 63

Page: 63 / 447

3.6

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual

Start engine and allow it to reach operating
temperature, monitoring gauge indication.

NOTE

Test results are based on the use of the recommended

engine oil (Polaris PS-4 or PS-4 Extreme Duty) at

operating temperature, and may vary considerably if

any other oil is used or if engine is not up to

temperature.

Oil Pressure Specification (Engine Hot):Minimum @

1200 RPM: 10 PSI

Upon assembly, torque the crankcase gallery plug to
specification.

TORQUE

Crankcase Gallery Plug:

11 ft-lbs (15 Nm)

ENGINE

Summary of Contents for RANGER CREW 900 2014
































































































































































































































































































































































































































































Search results

Summary of Contents for RANGER CREW 900 2014

Reviews:

Related manuals for RANGER CREW 900 2014

Brands by name

Popular brands

Polaris RANGER CREW 900 2014, Manual

Search results

Summary of Contents for RANGER CREW 900 2014

Reviews:

Related manuals for RANGER CREW 900 2014

Brands by name

Popular brands