Polaris RANGER CREW 900 2014 Manual Download Page 330

Page: 330 / 447

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual
© Copyright Polaris Sales Inc.

8.11

Install the (2) bolts (E) and transmission joint retainer
plate (F) on the right side. Hand tighten the bolts so
they remain loose at this time.

Install the (2) longer bolts into left side mounting
holes. Torque left side mounting bolts to specification
using the numbered sequence shown.

Torque right side mounting bolts to specification
using the numbered sequence shown.

TORQUE

Engine / Transmission Mounting Bolts:Step 1-2:

64 ft-

lbs (87 Nm)

Step 3:

5 ft-lbs (7 Nm)

Step 4-7:

44 ft-lbs

(60 Nm)

10. Remove the clutch center distance tool.

11. Remove the spacer or support between the vehicle

frame and engine.

12. Torque the rear transmission mount bolt (B) to

specification.

TORQUE

Rear Transmission Mount Bolt:

40 ft-lbs (54 Nm)

13. Remove the lifting straps and overhead or portable

hoist.

TRANSMISSION

Summary of Contents for RANGER CREW 900 2014
































































































































































































































































































































































































































































Search results

Summary of Contents for RANGER CREW 900 2014

Reviews:

Related manuals for RANGER CREW 900 2014

Brands by name

Popular brands

Polaris RANGER CREW 900 2014, Manual

Search results

Summary of Contents for RANGER CREW 900 2014

Reviews:

Related manuals for RANGER CREW 900 2014

Brands by name

Popular brands