Polaris RANGER CREW 900 2014 Manual Download Page 142

Page: 142 / 447

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual
© Copyright Polaris Sales Inc.

3.85

14. Install the appropriate tappet.

NOTE

Lubricate the outer portion of the valve bucket upon

installation.

15. Repeat steps 10-14 until all necessary valves have

been adjusted.

16. Reinstall the camshafts and camshaft carriers and

tighten the bolts evenly to specification.

TORQUE

Camshaft Carrier Bolts:

89 in-lbs (10 Nm)

17. Measure and confirm that valve clearance is now

within specification for each valve.

18. If valve clearance is not within specification, repeat

this procedure.

19. If all valve clearance measurements are now within

specification, remove the camshaft carriers and
proceed to Camshaft Installation / Timing, page 3.78.

ENGINE

Summary of Contents for RANGER CREW 900 2014
































































































































































































































































































































































































































































Search results

Summary of Contents for RANGER CREW 900 2014

Reviews:

Related manuals for RANGER CREW 900 2014

Brands by name

Popular brands

Polaris RANGER CREW 900 2014, Manual

Search results

Summary of Contents for RANGER CREW 900 2014

Reviews:

Related manuals for RANGER CREW 900 2014

Brands by name

Popular brands