Polaris RANGER CREW 900 2014 Manual Download Page 276

Page: 276 / 447

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual
© Copyright Polaris Sales Inc.

6.27

Inspect the bearings inside the moveable sheave.

Moveable Sheave Bearing Inspection:

Replace the clutch assembly if more brass than Teflon®

is visible on the bearing.

10. Inspect driven clutch sheave faces for wear or

damage.

11. Clean and inspect splines on helix and transmission

input shaft.

12. Lube splines with a light film of grease.

Do not

lubricate the bearings!

CLUTCH ASSEMBLY

Install the inner spring retainer if removed.

Do not

apply oil or grease to the bearings.

Align the “X” marks on each of the sheaves during
reassembly.

Install the spring into the inner retainer.

Install the spacer over the shaft.

CLUTCHING

Summary of Contents for RANGER CREW 900 2014
































































































































































































































































































































































































































































Search results

Summary of Contents for RANGER CREW 900 2014

Reviews:

Related manuals for RANGER CREW 900 2014

Brands by name

Popular brands

Polaris RANGER CREW 900 2014, Manual

Search results

Summary of Contents for RANGER CREW 900 2014

Reviews:

Related manuals for RANGER CREW 900 2014

Brands by name

Popular brands