Polaris RANGER CREW 900 2014 Manual Download Page 239

Page: 239 / 447

5.40

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual

Tighten the Press Asm. screw and fully remove the
ball joint from the A-arm.

BALL JOINT INSTALLATION

By hand, install the NEW ball joint into the A-arm.

Position the Installation Adapter (D) over the face of
the ball joint.

Position the Spacer (A) over the shaft of the ball joint
so it is against the A-arm.

Install the Press Asm. (C) onto the A-arm to engage
the Installation Adapter and Spacer.

Tighten the Press Asm. screw and fully install the
ball joint into the arm.

After the new ball joint is fully installed into the A-
arm, install a new retaining ring.

Repeat the ball joint service procedure for any
additional A-arm ball joint replacements.

Insert upper / lower A-arm ball joint end into the
bearing carrier. Install new pinch bolts and nuts.
Torque to specification.

If needed, install new brake caliper mounting bolts
and torque to specification.

CAUTION

New bolts have a pre-applied locking agent which is

destroyed upon removal. Always use new brake caliper

mounting bolts upon assembly.

BODY / STEERING / SUSPENSION

Summary of Contents for RANGER CREW 900 2014
































































































































































































































































































































































































































































Search results

Summary of Contents for RANGER CREW 900 2014

Reviews:

Related manuals for RANGER CREW 900 2014

Brands by name

Popular brands

Polaris RANGER CREW 900 2014, Manual

Search results

Summary of Contents for RANGER CREW 900 2014

Reviews:

Related manuals for RANGER CREW 900 2014

Brands by name

Popular brands