Polaris RANGER CREW 900 2014 Manual Download Page 395

Page: 395 / 447

10.10

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual

INSTRUMENT CLUSTER

OVERVIEW

The instrument cluster displays critical vehicle information to the user. Reference the following page for display
functions and descriptions.

NOTE

Some features are not applicable to all models.

The use of a high pressure washer may damage the instrument cluster. Wash the vehicle by hand or with a garden

hose using mild soap. Certain products, including insect repellents and chemicals, will damage the instrument cluster

lens. Do not use alcohol to clean the instrument cluster. Do not allow insect sprays to contact the lens. Immediately

clean off any gasoline that splashes on the instrument cluster.

ELECTRICAL

Summary of Contents for RANGER CREW 900 2014
































































































































































































































































































































































































































































Search results

Summary of Contents for RANGER CREW 900 2014

Reviews:

Related manuals for RANGER CREW 900 2014

Brands by name

Popular brands

Polaris RANGER CREW 900 2014, Manual

Search results

Summary of Contents for RANGER CREW 900 2014

Reviews:

Related manuals for RANGER CREW 900 2014

Brands by name

Popular brands