Polaris RANGER CREW 900 2014 Manual Download Page 368 | Manualshive

Page: 368 / 447

background image

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual
© Copyright Polaris Sales Inc.

9.15

5.

Install the pad adjuster set screw and turn clockwise
until stationary pad contacts disc, then back off 1/2
turn (counterclockwise).

6.

Verify fluid level in reservoir is up to MAX line inside
reservoir and install reservoir cap.

Master Cylinder FluidUp to MAX line inside reservoir

7.

Install wheel and torque wheel nuts to specification.

TORQUE

Wheel Nuts:

Steel Wheels: 60 ft-lbs (81 Nm)

Aluminum Wheels: 120 ft-lbs (163 Nm)

BRAKE BURNISHING PROCEDURE

It is required that a burnishing procedure be performed
after installation of new brake pads to extend service life
and reduce noise.

Start machine and slowly increase speed to 30 mph.
Gradually apply brakes to stop machine. Allow pads and
disc to cool sufficiently during the procedure. Do not
allow pads or disc to become hot or warping may result.
Repeat this procedure 10 times.

Do not make more

than 3 stops per 1 mile (1.6 km).

«
...
366
367
368
369
370
...
»

Summary of Contents for RANGER CREW 900 2014
































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RANGER CREW 900 2014

Brand: GEDA Pages: 36

Brand: E-TON Pages: 34

Transporta CCT 5221

Brand: Ifor Williams Trailers Pages: 45

Wagon with tilt

Brand: Texas Pages: 42

DEFENDER MAX Series 2021

Brand: Can-Am Pages: 211

No Limit SL50 Compact

Brand: MGI Pages: 15

OneStopGardens 91240

Brand: Harbor Freight Tools Pages: 7

Brand: Traxxas Pages: 26

Brand: Jacobsen Pages: 60

Brand: Let's Go Aero Pages: 3

Brand: Yerf-Dog Pages: 40

Brand: Coleman Powersports Pages: 45

EVINRUDE Johnson 5007118

Brand: BRP Pages: 14

Brand: Yamaha Pages: 44

Stand-Up SINGLE RIDE-UP Go Series

Brand: Kendon Pages: 20

Bomag MPH 122-2

Brand: Fayat Group Pages: 198

Brand: Wallenstein Pages: 45

Brand: Honda Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands