Polaris RANGER CREW 900 2014 Manual Download Page 103

Page: 103 / 447

3.46

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual

ENGINE DISASSEMBLY / INSPECTION - LOWER END

STATOR COVER REMOVAL / INSPECTION

NOTE

The stator cover can be removed with the engine

installed in the chassis.

Remove the thirteen screws retaining the stator
cover.

CAUTION

The flywheel contains powerful magnets. Use caution

when removing and installing the stator cover. DO NOT

place fingers between cover and crankcase at any time

during the removal / installation process or injury could

result.

Carefully pry the stator cover off the engine using the
two pry areas as shown below.

Inspect the condition of the stator windings

and

output wires

. If replacement is required, refer to

Chapter 10.

Inspect the ball bearing that supports the starter
motor shaft.

ENGINE

Summary of Contents for RANGER CREW 900 2014
































































































































































































































































































































































































































































Search results

Summary of Contents for RANGER CREW 900 2014

Reviews:

Related manuals for RANGER CREW 900 2014

Brands by name

Popular brands

Polaris RANGER CREW 900 2014, Manual

Search results

Summary of Contents for RANGER CREW 900 2014

Reviews:

Related manuals for RANGER CREW 900 2014

Brands by name

Popular brands