Polaris RANGER CREW 900 2014 Manual Download Page 370

Page: 370 / 447

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual
© Copyright Polaris Sales Inc.

9.17

Remove the two caliper mounting bolts (C) and
caliper.

CALIPER DISASSEMBLY

Remove both brake pads from the caliper (see
“FRONT BRAKE PADS - Pad Removal”).

Remove the mount bracket assembly and dust boots
from

caliper.

Thoroughly

clean

caliper

before

disassembly and prepare a clean work area.

Use a commercially available caliper piston pliers to
extract the pistons from the caliper.

NOTE

Do not remove the caliper pistons with a standard

pliers. The piston sealing surfaces will become

damaged if a standard pliers is used.

BRAKES

Summary of Contents for RANGER CREW 900 2014
































































































































































































































































































































































































































































Search results

Summary of Contents for RANGER CREW 900 2014

Reviews:

Related manuals for RANGER CREW 900 2014

Brands by name

Popular brands

Polaris RANGER CREW 900 2014, Manual

Search results

Summary of Contents for RANGER CREW 900 2014

Reviews:

Related manuals for RANGER CREW 900 2014

Brands by name

Popular brands