Circuit-, IC descriptions and list of abbreviations
EN 179
HDRW720/0x, DVDR725H/0x
9.
AD1852
PIN FUNCTION DESCRIPTIONS
Pin
Input/Output
Pin Name
Description
1
I
DGND
Digital Ground.
2
I
MCLK
Master Clock Input. Connect to an external clock source at either 256 F
S
, 384 F
S
,
512 F
S
, 768 F
S
, or 1024 F
S
.
3
I
CLATCH
Latch Input for Control Data. This input is rising-edge sensitive.
4
I
CCLK
Control Clock Input for Control Data. Control input data must be valid on the rising
edge of CCLK. CCLK may be continuous or gated.
5
I
CDATA
Serial Control Input, MSB first, containing 16 bits of unsigned data per channel. Used
for specifying channel-specific attenuation and mute.
6
NC
No Connect.
7
I
192/
48
Selects 48 kHz (LO) or 192 kHz Sample Frequency.
8
O
ZEROR
Right Channel Zero Flag Output. This pin goes HI when Right Channel has no signal
input for more than 1024 LR Clock Cycles.
9
I
DEEMP
De-Emphasis. Digital de-emphasis is enabled when this input signal is HI. This is used
to impose a 50
µ
s/15
µ
s response characteristic on the output audio spectrum at an
assumed 44.1 kHz sample rate. Curves for 32 kHz and 48 kHz sample rates may be
selected via SPI control register.
10
I
96/
48
Selects 48 kHz (LO) or 96 kHz Sample Frequency.
11, 15
I
AGND
Analog Ground.
12
O
OUTR+
Right Channel Positive Line Level Analog Output.
13
O
OUTR–
Right Channel Negative Line Level Analog Output.
14
O
FILTR
Voltage Reference Filter Capacitor Connection. Bypass and decouple the voltage refer-
ence with parallel 10
µ
F and 0.1
µ
F capacitors to the AGND.
16
O
OUTL–
Left Channel Negative Line Level Analog Output.
17
O
OUTL+
Left Channel Positive Line Level Analog Output.
18
I
AVDD
Analog Power Supply. Connect to Analog 5 V Supply.
19
FILTB
Filter Capacitor Connection. Connect 10
µ
F capacitor to AGND (Pin 15).
20
I
IDPM1
Input Serial Data Port Mode Control One. With IDPM0, defines 1 of 4 serial modes.
21
I
IDPM0
Input Serial Data Port Mode Control Zero. With IDPM1, defines 1 of 4 serial modes.
22
O
ZEROL
Left Channel Zero Flag Output. This pin goes HI when Left Channel has no signal
input for more than 1024 LR Clock Cycles.
23
I
MUTE
Mute. Assert HI to mute both stereo analog outputs. Deassert LO for normal operation.
24
I
RESET
Reset. The AD1852 is reset on the rising edge of this signal. The serial control port
registers are reset to the default values. Connect HI for normal operation.
25
I
L/
R
CLK
Left/
Right
Clock Input for Input Data. Must run continuously.
26
I
BCLK
Bit Clock Input for Input Data. Need not run continuously; may be gated or used in a
burst fashion.
27
I
SDATA
Serial Input, MSB first, containing two channels of 16, 18, 20, and 24 bits of twos
complement data per channel.
28
I
DVDD
Digital Power Supply Connect to digital 5 V supply.
Table I. Serial Data Input Mode
IDPM1 (Pin 20)
IDPM0 (Pin 21)
Serial Data Input Format
0
0
Right-Justified
0
1
I
2
S-Compatible
1
0
Left-Justified
1
1
DSP
Summary of Contents for DVDR725H
Page 148: ...EN 148 HDRW720 0x DVDR725H 0x 7 Circuit Diagrams and PWB Layouts ...
Page 171: ...Circuit IC descriptions and list of abbreviations EN 171 HDRW720 0x DVDR725H 0x 9 Figure 9 11 ...
Page 172: ...Circuit IC descriptions and list of abbreviations EN 172 HDRW720 0x DVDR725H 0x 9 Figure 9 12 ...
Page 193: ...Circuit IC descriptions and list of abbreviations EN 193 HDRW720 0x DVDR725H 0x 9 ...
