PG D
RIVES
T
ECHNOLOGY
O
MNI
– S
TANDARD
- P
ROGRAMMING
SK78813/5
90
The effect of List is to list all the available Profiles for the Mode. In this case, all
the available Drive Profiles. The first number denotes the actual Profile number,
while the text will be as set by the standard R-net parameter, Profile Name. A
right SID command will enter the highlighted Profile.
Assume Position 1 = Drive and Position 1 Type = Select, then the menu item
would appear as below.
Profile
< 3 >
The effect of Select is to allow a new Profile to be selected, but not necessarily
entered. Selection is via left and right SID commands. There would be a further
menu item, Drive, that would enter Drive Mode in the selected Profile. This
method reflects the functionality of the Pilot+ Omni+
All these examples use Drive Mode, which conventionally has multiple Profiles.
However, other Modes are generally only present in one Profile; meaning that,
in practice, a setting of Entry will be the most commonly used for non-Drive
Modes. However, for completeness, the Omni does offer the capability of
working with multiple Profiles in non-Drive Modes. Again, this is best explained in
an example, as follows.
Assume it is required to have non-latched and latched seating control. This can
be achieved by enabling Seating Mode in two Profiles via the standard R-net
parameter, Mode Enable. The conventional way of doing this would be settings
such as below. Latched seating control would also need to be set in one of the
Profiles via the standard R-net parameter, Latched Actuators.
Profile 1
Profile 1
Profile 1
Profile 1
Profil
Profil
Profil
Profile 2
e 2
e 2
e 2
Profile 3
Profile 3
Profile 3
Profile 3
Profile 4
Profile 4
Profile 4
Profile 4
Profile 5
Profile 5
Profile 5
Profile 5
Mode Enable
Mode Enable
Mode Enable
Mode Enable
12
12
1
1
1
Assume Position 1 = Seating and Position 1 Type = Entry, then the menu item
would appear as below.
Seating
>
The effect of Entry is to display the Mode Name and an entry >. A right SID
command will enter the Mode. The Mode will be entered in the Profile in which
it was last used
Summary of Contents for R-NET OMNI
