PG Drives Technology R-NET OMNI Technical Manual Download Page 55 | Manualshive

Page: 55 / 174

background image

PG D

RIVES

T

ECHNOLOGY

O

MNI

– S

TANDARD

- O

PERATION

SK78813/5

55

The clock is user adjustable. Adjustable options are:

•

Visibility, whether the clock is displayed on screen.

•

The display format, 12 or 24 hour.

•

The time, the user can adjust the time.

These adjustments are made within User Menu/Settings.

11.3.3 Selected Direction Indicator

Forwards

Reverse

These are only displayed if the Omni has been configured to use a 3 axis
proportional SID. Refer to the Operation with 3-axis Proportional and Switch type
SIDs (Head Arrays).

11.3.4 Speed Display

This gives a proportional display of the wheelchairs speed. The Arc begins at 0%
and has a programmable maximum. The programmable parameter is Max
Displayed Speed. Refer to the Programming Chapter.

11.3.5 Digital Speed Display

This displays the actual speed of the wheelchair derived
from the motors. The display can be set to mph of km/h.

These adjustments can be made in the OBP Menu.

«
...
53
54
55
56
57
...
»

Summary of Contents for R-NET OMNI















































































































































































Reviews:

No comments

Related manuals for R-NET OMNI

Brand: panthera Pages: 9

Brand: panthera Pages: 9

Brand: Handicare Pages: 44

Brand: Handicare Pages: 32

ZT-600-710-SP16

Brand: Z-Tec Pages: 7

Brand: Küschall Pages: 56

Brand: Jazzy Pages: 29

Brand: Welby Pages: 20

Glideabout Commode

Brand: Ultimate Healthcare Pages: 3

Brand: Karman Pages: 12

Brand: TA Service Pages: 76

Mio Carbon Design 2018

Brand: SORG Pages: 32

Brand: Kids UP Pages: 28

Brand: AccessRec Pages: 7

Brand: Ossenberg Pages: 2

Brand: Z-Tec Pages: 12

Pyro Start Plus

Brand: B+B Pages: 23

Brand: B+B Pages: 67

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands