PG Drives Technology R-NET OMNI Technical Manual Download Page 22 | Manualshive

Page: 22 / 174

background image

PG D

RIVES

T

ECHNOLOGY

O

MNI

– S

TANDARD

- I

NSTALLATION

SK78813/5

22

2.8

Communications Connector

This connector links the Omni to the R-net system.

2.9

9-way D-type Specialty Input Device (SID) Connectors

These  provide  connections  to  analogue  or  digital  SIDs.  There  is  a  facility  to
detect  if  a  mating  connector  is  in  place;  and  provision  of  a  low  current  12V
supply.  Refer  to  the  Specifications  Chapter  for  full  details  of  the  electrical
specifications.

2.10 User Switch Jacks

There are two 3.5mm/1/8” jack sockets which provide connection to the User
Switches. Full details of User Switches are given in the section Connection of
SIDs.

There is also facility to detect if the mating User Switch jack plug is in place.
Refer to the Specifications Chapter for full details of the electrical specifications.

2.11

External On/Off Switch Input

This is a 3.5mm/1/8” jack socket which provides connection to a user operated
On/Off button. This connection is optional and the Omni will function normally
without it.

2.12

Sip and Puff Input

This input will accept a 3.5mm/1/8” pipe connected to a Sip and Puff
mouthpiece. For full specification refer to the Specifications Chapter.

«
...
20
21
22
23
24
...
»

Summary of Contents for R-NET OMNI















































































































































































Reviews:

No comments

Related manuals for R-NET OMNI

Brand: VA Health care Pages: 18

Brand: Everest & Jennings Pages: 32

Brand: Coopers Pages: 4

Brand: Electra Pages: 63

Brand: E&J Pages: 28

Brand: Pride Pages: 39

Brand: Power Plus Mobility Pages: 6

Brand: Golden Pages: 30

Compass HD GP620CC

Brand: Golden Pages: 32

Brand: EZee Life Pages: 2

Saber GT Series

Brand: Karma Pages: 64

Brand: Mangar Pages: 12

Brand: Sanction Industry Pages: 2

Brand: Invacare Pages: 2

Brand: Invacare Pages: 2

Brand: Invacare Pages: 8

Junior Vector O2

Brand: Vicair Pages: 6

Brand: Shoprider Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands