PG Drives Technology R-NET OMNI Technical Manual Download Page 132 | Manualshive

Page: 132 / 174

background image

PG D

RIVES

T

ECHNOLOGY

O

MNI

– IR

SK78813/5

132

8

Configuration

8.1

Configuration of IR Control Mode

PGDT  factory  programming  configures  Mode  7  to  be  IR  Control  Mode.  If  this
programming has been overwritten, then it may be necessary to re-program as
described  below.    You  will  know  if  re-programming  is  necessary  if  you  cannot
access  the  IR  User  Menu  when  it  has  learnt  codes.  In  this  instance,
programming as below is recommended.

Firstly, determine which Modes are not used. In the sample screen shown
below, it is Modes 5, 6 and 7, and Mode 7 is the one that has been chosen for
IR Control Mode.

8.2

Mode Name

This is a 20 character text string that sets the name of the selected Mode. The
sample screen above shows it as still being named Mode 7, but it could be
changed to something more specific, such as IR Control

8.3

Input

This parameter should be set Raw.

8.4

Output

This parameter should be set to IR Control.

The OEM may have factory preset set these options.

«
...
130
131
132
133
134
...
»

Summary of Contents for R-NET OMNI















































































































































































Reviews:

No comments

Related manuals for R-NET OMNI

Brand: Invacare Pages: 108

Brand: SOMA Pages: 32

Brand: Electra Pages: 63

Brand: Quantum Pages: 2

Brand: Quantum Pages: 2

Brand: Quantum Pages: 39

Brand: HMN Pages: 12

Brand: Eagle Health Supplies Pages: 2

Sopur Ti Titanium

Brand: Quickie Pages: 216

Brand: Making Life Easy Pages: 2

Brand: Unicare Health Pages: 12

Brand: rainbow care Pages: 4

Brand: R82 Pages: 8

Brand: Vermeiren Pages: 152

Brand: Invacare Pages: 2

Storm Torque SP

Brand: Invacare Pages: 4

top end pro 2 all sport

Brand: Invacare Pages: 16

Brand: Invacare Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands