PG Drives Technology R-NET OMNI Technical Manual Download Page 36 | Manualshive

Page: 36 / 174

PG Drives Technology R-NET OMNI Technical Manual Download Page 36

PG D

RIVES

T

ECHNOLOGY

O

MNI

– S

TANDARD

- I

NSTALLATION

SK78813/5

36

A long operation while not driving will put the Omni to sleep. To wake the Omni,
a short operation of the User Switch is required.

The time of a long operation is preset to 1 Second, but it is programmable from
0.5 to 5.0 Seconds via the parameter Switch Long. See section Switch Long in
the Programming chapter for more details.

There is a further programmable parameter associated with the operation of
the User Switch, Switch Medium. This parameter is only applicable with 3-axis
type SIDs, i.e. 3 switch head controls. Refer to the Programming Chapter for full
details of this function.

9.2

Accessing Wheelchair Functions

The Omni can be programmed to access all the available wheelchair
functions in two ways – by Menu or by Sequence. The programmable
parameter that sets the access method is User Control.

The  Menu  method  is  whereby  an  activation  of  the  User  Switch  while  in  Drive
Mode  will  bring  up  an  on-screen  User  Menu  as  shown  below.  SID  direction
commands are then used to navigate the menu and select functions.

The Sequence method is whereby successive activations of the User Switch will
sequentially access all the wheelchair functions.

It  is  not  advisable  to  program  the  menu  options,
‘speed  adjust’  or  ‘profile  select’,  if  the  Sequence
method  is  being  used  with  scanning  operation.  Refer
to the Programming Chapter for further details.

«
...
34
35
36
37
38
...
»

Summary of Contents for R-NET OMNI















































































































































































Reviews:

No comments