PG Drives Technology R-NET OMNI Technical Manual Download Page 108 | Manualshive

Page: 108 / 174

background image

PG D

RIVES

T

ECHNOLOGY

O

MNI

– A

DVANCED

-P

ROGRAMMING

SK78813/5

108

If the Omni is setup as:

Position 1 = Drive

Position 1 Type = List

Position 1 = 1beep

Position 2 = 2 beeps

Then the User Menu would appear as:

1: Profile 1

2: Profile 2

3: Profile 3

Seating

For  the  top  3  lines,  there  would  only  be  1  beep,  as  those  lines  all  relate  to
Position  1.  For  the  fourth  line,  there  would  be  2  beeps,  as  that  line  effectively
relates  to  Position  2.  Therefore,  in  this  instance,  a  more  sensible  programming
arrangement may be.

Position 1 = Drive

Position 1 Type = List

Position 1 = 0 beep

Profile Identifier # = On

Position 2 = 4 beeps

This would result in 1 to 3 beeps for the first 2 lines and 4 beeps for the fourth
line.

«
...
106
107
108
109
110
...
»

Summary of Contents for R-NET OMNI















































































































































































Reviews:

No comments

Related manuals for R-NET OMNI

Brand: Neatech Pages: 40

Quantum 600 2HD

Brand: Pride Mobility Pages: 43

Otto Bock Back 1

Brand: Otto Bock Pages: 77

Brand: Permobil Pages: 24

Brand: Permobil Pages: 31

Comfort Cushions ACTA-EMBRACE

Brand: Permobil Pages: 48

Brand: KOMFI-RIDER Pages: 20

Brand: Medicare Technology Pages: 22

Q6 Edge 3 STRETTO

Brand: Quantum Pages: 24

Brand: Quantum Pages: 55

multichair 4000

Brand: Nuprodx Pages: 9

Brand: Harbor Freight Tools Pages: 12

Brand: Vermeiren Pages: 8

Brand: Borringia Pages: 8

Brand: Repose Pages: 2

ELECTRIC WHEELCHAIRS

Brand: Handicare Pages: 64

Lille Viking 2000+

Brand: Etac Pages: 60

Mio Carbon Design 2018

Brand: SORG Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands