PG Drives Technology R-NET OMNI Technical Manual Download Page 149 | Manualshive

Page: 149 / 174

background image

PG D

RIVES

T

ECHNOLOGY

O

MNI

– D

IAGNOSTICS

SK78813/5

149

3.14 Overtemp (acts)

This occurs when the control system detects that the ISM’s actuator circuitry has
become too hot. The control system will cease drive to the actuator motor in
question.

•

Allow the ISM to cool.

•

If the ISM is frequently overheating check the condition of the
actuator motors and the connections to them.

•

If the trip persists contact your service agent.

3.15

Overtemp (lamps)

This occurs when the control system detects that ISM’s lighting circuitry has
become too hot. The control system will cease supplying current to the lamp in
question.

•

Allow the ISM to cool.

•

If the ISM is frequently overheating check the condition of all the
connected bulbs and lamps.

•

If the trip persists contact your service agent.

3.16

DIME Error

This occurs when the control system detects an identification conflict between
two modules in the system.

If a new module has been introduced:

•

Disconnect the new module and cycle the power.

•

If no trip is present connect the new module to the system and
cycle the power.

•

If the trip reappears then the new module must be the cause of
the problem.

If there has been no additions:

•

Disconnect one module at a time and cycle the power.

«
...
147
148
149
150
151
...
»

Summary of Contents for R-NET OMNI















































































































































































Reviews:

No comments

Related manuals for R-NET OMNI

Brand: Quickie Pages: 24

Brand: I-GO Pages: 28

esprit action4 NG

Brand: Invacare Pages: 32

Brand: C.T.M. Pages: 20

Brand: Golden Technologies Pages: 38

Brand: Motion Composites Pages: 24

Brand: Rebotec Pages: 8

Brand: Rebotec Pages: 12

Brand: Coopers Pages: 4

Rigid Aero Z Series

Brand: TiLite Pages: 102

Brand: HMN Pages: 5

Brand: ROHO Pages: 11

Brand: Dahlia Pages: 40

Brand: Glide Pages: 33

Brand: Vermeiren Pages: 120

Brand: Permobil Pages: 47

Brand: Safer Locks Pages: 16

Brand: Safer Locks Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands