PG Drives Technology R-NET OMNI Technical Manual Download Page 170 | Manualshive

Page: 170 / 174

background image

PG D

RIVES

T

ECHNOLOGY

O

MNI

– W

ARNING

S

UMMARY

SK78813/5

170

2.3

Installing the SID onto a Powerchair

The  SID  should  be  fitted  to  the  powerchair  in
accordance with the instructions of both the SID and
powerchair  manufacturers.  PG  Drives  Technology
accept  no  liability  for  losses  of  any  kind  resulting
from  an  incorrect  installation  of  a  SID.  Chapter  1
section 6.

2.4

User Switch

For a truly fail-safe system a normally closed User
Switch is recommended. This ensures that, if the
switch

becomes

accidentally

disconnected

the

powerchair  will  default  to  a  stopped  condition.  It  is
possible  to  configure  the  Omni  to  function  with
normally  open  switch  types,  see  section  User  Switch
in  the  Programming  chapter  for  details.  PG  Drives
Technology  recommend  that,  whenever  possible,  a
normally  closed  switch  should  be  used.  If  a  normally
open  switch  is  used  the  responsibility  for  that
decision  lies  with  the  healthcare  professional.  PG
Drives  Technology  accept  no  liability  for  any  losses
resulting  from  the  use  of  a  non-normally  closed User
Switch.

Because  a  disconnected  User  Switch  means  there  is
no  emergency  stop  function,  PG  Drives  Technology
recommend  that  Switch  Detect  is  always  set  to  On.
PG  Drives  Technology  will  accept  no  liability  for  any
losses  resulting  from  any  other  setting  of  this
parameter. Chapter 1 section 6.2.

2.5

D-type Connector

The SID’s D-type connector should always be fitted
with gold contacts and a suitable backshell with
locking screws. The locking screws should be used to

«
...
168
169
170
171
172
...
»

Summary of Contents for R-NET OMNI















































































































































































Reviews:

No comments

Related manuals for R-NET OMNI

MOPEDIA RC220-43

Brand: Moretti Pages: 20

Brand: Dynamic Pages: 27

Brand: Invacare Pages: 2

Brand: Invacare Pages: 30

Brand: Invacare Pages: 78

Brand: Invacare Pages: 88

Brand: Invacare Pages: 116

Brand: Invacare Pages: 8

Brand: Invacare Pages: 32

Brand: Invacare Pages: 139

Deluxe Bariatric Drop-Arm Commode

Brand: Drive Medical Pages: 2

Drive viper plus gt

Brand: Drive Medical Pages: 8

Travelite Chair In A Bag

Brand: Drive Pages: 30

Brand: Blumil Pages: 12

Brand: CareCo Pages: 11

Brand: Enigma Pages: 6

Brand: B+B Pages: 38

Stealth Positioning Pelvic Belts

Brand: Stealth Products Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands