PG Drives Technology R-NET OMNI Technical Manual Download Page 147

Page: 147 / 174

PG D

RIVES

ECHNOLOGY

MNI

– D

IAGNOSTICS

SK78813/5

147

If the trip is still present after the above has been attempted, then the Omni
may be defective. Refer to Section 5.

3.8

Latched Timeout

This  occurs  when  the  control  system  detects  that  the  Latched  Timeout
programmed  time  has  been  exceeded.  For  example,  the  Input  Device,
Joystick,  Head  Array,  Sip  and  Puff,  etc.  has  not  been  operated  frequently
enough.

The trip is a notification of why the control system has dropped out of Latched
Mode.

•

Cycle the power.

•

Initiate Latched Mode.

If the trip is still present after the above checks have been made, then the Input
Device may be defective. Refer to Section 5.

3.9

Brake Lamp Short

This occurs when the control system detects a short in the Brake Lamp Circuit.
Refer to section 2.3 for connection details.

•

Check the brake lamps, cables and connections to the control
system.

If the trip is still present after the above checks have been made, then the ISM
may be defective. Refer to Section 5.

3.10 Lamp Short

This occurs when the control system detects a short in either of the Lamp
Circuits. Refer to section 2.3 for connection details.

7205 -

Left Lamp Short

7209 -

Right Lamp Short

•

Check the lamps, cables and connections to the control system.

If the trip is still present after the above checks have been made, then the ISM
may be defective. Refer to Section 5.

Summary of Contents for R-NET OMNI















































































































































































Search results

Summary of Contents for R-NET OMNI

Reviews:

Related manuals for R-NET OMNI

Brands by name

Popular brands

PG Drives Technology R-NET OMNI, Technical Manual

Search results

Summary of Contents for R-NET OMNI

Reviews:

Related manuals for R-NET OMNI

Brands by name

Popular brands