PerkinElmer L1050045 Getting Started Manual Download Page 3

Page: 3 / 60

Spectrum RX I Getting Started Guide . 3

Contents

Contents ................................................................................................... 3

Using this Manual ...................................................................................... 4

Part Numbers ...................................................................................... 4

Conventions Used in this Manual................................................................. 5

Notes, cautions and warnings............................................................... 5

Documentation Conventions................................................................. 8

Warnings and Safety Information................................................................ 9

Summary ............................................................................................ 9

General Safety................................................................................... 10

Location and Ventilation..................................................................... 11

Electrical Safety................................................................................. 11

EMC Compliance................................................................................ 12

Spectrum RX I Laser Product Classification.......................................... 13

Laser Labels and Laser Apertures ....................................................... 14

System Requirements .............................................................................. 17

Electrical Requirements...................................................................... 17

Site Requirements ............................................................................. 17

Unpacking the Spectrum RX I ................................................................... 19

Moving the Spectrum RX I.................................................................. 19

Opening the Shipping Containers........................................................ 20

Unpacking the Spectrum RX I............................................................. 21

Removing the Packaging .................................................................... 21

Changing the Desiccant...................................................................... 24

Locating the Interferometer Adjustment Screws .................................. 27

Unpacking the Screen ........................................................................ 30

Installation .............................................................................................. 33

Resetting the Date of Previous Desiccant Change ................................ 35

Adjusting the Interferometer .............................................................. 39

Contacting PerkinElmer ...................................................................... 43

Storing the Results of the Installation ................................................. 43

Determining the Signal-to-Noise Ratio....................................................... 46

Scanning and Viewing a Spectrum ............................................................ 49

Collecting a Background..................................................................... 49

Using the View Keys .......................................................................... 53

Autex................................................................................................ 55

Adjusting the Interferometer .................................................................... 56

Related Documents.................................................................................. 59

Summary of Contents for L1050045





























































Search results

Summary of Contents for L1050045

Reviews:

Related manuals for L1050045

Brands by name

Popular brands

PerkinElmer L1050045, Getting Started Manual

Search results

Summary of Contents for L1050045

Reviews:

Related manuals for L1050045

Brands by name

Popular brands