Panasonic WV-SUD638 Operating Instructions Manual Download Page 126

Page: 126 / 212

12 Configuring the network settings [Network]

The network settings can be configured on the “Network” page.
The “Network” page has the [Network] tab and the [Advanced] tab.

12.1 Configure the network settings [Network]

Click the [Network] tab on the “Network” page. (

page 32, page 34 )

The following information is required to configure the network settings. Contact the network administrator or
your Internet service provider.

•

IP address

•

Subnet mask

•

Default gateway (when using the gateway server/router)

•

HTTP port

•

Primary DNS address, Secondary DNS address (when using DNS)

126

Operating Instructions

12 Configuring the network settings [Network]

Summary of Contents for WV-SUD638





















































































































































































































Search results

Summary of Contents for WV-SUD638

Reviews:

Related manuals for WV-SUD638

Brands by name

Popular brands

Panasonic WV-SUD638, Operating Instructions Manual

Search results

Summary of Contents for WV-SUD638

Reviews:

Related manuals for WV-SUD638

Brands by name

Popular brands